Add Makefiles for TMK converters.
This commit is contained in:
tmk
parent
110eea578b
commit
7209c1d387
|
|
@ -1,3 +1,6 @@
|
|||
#
|
||||
# Makefile for Teensy
|
||||
#
|
||||
# Target file name (without extension).
|
||||
TARGET = ps2_usb_lufa
|
||||
|
||||
|
|
@ -59,7 +62,7 @@ ARCH = AVR8
|
|||
F_USB = $(F_CPU)
|
||||
|
||||
# Interrupt driven control endpoint task(+60)
|
||||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
||||
#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
||||
|
||||
|
||||
# Boot Section Size in *bytes*
|
||||
|
|
@ -68,7 +71,7 @@ OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
|||
# Atmel DFU loader 4096
|
||||
# LUFA bootloader 4096
|
||||
# USBaspLoader 2048
|
||||
OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
||||
OPT_DEFS += -DBOOTLOADER_SIZE=512
|
||||
|
||||
|
||||
# Build Options
|
||||
|
|
|
|||
|
|
@ -1,75 +0,0 @@
|
|||
# Target file name (without extension).
|
||||
TARGET = ps2_usb_jis
|
||||
|
||||
# Directory common source filess exist
|
||||
TOP_DIR = ../..
|
||||
|
||||
# Directory keyboard dependent files exist
|
||||
TARGET_DIR = .
|
||||
|
||||
|
||||
# MCU name, you MUST set this to match the board you are using
|
||||
# type "make clean" after changing this, so all files will be rebuilt
|
||||
#MCU = at90usb162 # Teensy 1.0
|
||||
MCU = atmega32u4 # Teensy 2.0
|
||||
#MCU = at90usb646 # Teensy++ 1.0
|
||||
#MCU = at90usb1286 # Teensy++ 2.0
|
||||
|
||||
|
||||
# Processor frequency.
|
||||
# Normally the first thing your program should do is set the clock prescaler,
|
||||
# so your program will run at the correct speed. You should also set this
|
||||
# variable to same clock speed. The _delay_ms() macro uses this, and many
|
||||
# examples use this variable to calculate timings. Do not add a "UL" here.
|
||||
F_CPU = 16000000
|
||||
|
||||
|
||||
# Build Options
|
||||
# *Comment out* to disable the options.
|
||||
#
|
||||
MOUSEKEY_ENABLE = yes # Mouse keys
|
||||
EXTRAKEY_ENABLE = yes # Audio control and System control
|
||||
NKRO_ENABLE = yes # USB Nkey Rollover
|
||||
|
||||
#PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened)
|
||||
#PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin
|
||||
PS2_USE_BUSYWAIT = yes # uses primitive reference code
|
||||
|
||||
|
||||
# keyboard dependent files
|
||||
SRC = keymap_jis.c \
|
||||
matrix.c \
|
||||
led.c
|
||||
|
||||
|
||||
ifdef PS2_USE_USART
|
||||
SRC += protocol/ps2_usart.c
|
||||
OPT_DEFS += -DPS2_USE_USART
|
||||
endif
|
||||
ifdef PS2_USE_INT
|
||||
SRC += protocol/ps2.c
|
||||
OPT_DEFS += -DPS2_USE_INT
|
||||
endif
|
||||
ifdef PS2_USE_BUSYWAIT
|
||||
SRC += protocol/ps2.c
|
||||
OPT_DEFS += -DPS2_USE_BUSYWAIT
|
||||
endif
|
||||
|
||||
|
||||
#CONFIG_H = config_pjrc_usart.h
|
||||
CONFIG_H = config.h
|
||||
|
||||
|
||||
#---------------- Programming Options --------------------------
|
||||
PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
|
||||
|
||||
|
||||
# Search Path
|
||||
VPATH += $(TARGET_DIR)
|
||||
VPATH += $(TOP_DIR)
|
||||
|
||||
|
||||
include $(TOP_DIR)/protocol/pjrc.mk
|
||||
include $(TOP_DIR)/protocol.mk
|
||||
include $(TOP_DIR)/common.mk
|
||||
include $(TOP_DIR)/rules.mk
|
||||
|
|
@ -0,0 +1,98 @@
|
|||
#
|
||||
# Makefile for TMK keyboard converter rev2
|
||||
# https://github.com/tmk/keyboard_converter#pcb-rev1
|
||||
#
|
||||
# Target file name (without extension).
|
||||
TARGET = ps2_usb_tmk_rev1
|
||||
|
||||
# Directory common source filess exist
|
||||
TOP_DIR = ../..
|
||||
|
||||
# Directory keyboard dependent files exist
|
||||
TARGET_DIR = .
|
||||
|
||||
# project specific files
|
||||
SRC = keymap_common.c \
|
||||
matrix.c \
|
||||
led.c
|
||||
|
||||
ifdef KEYMAP
|
||||
SRC := keymap_$(KEYMAP).c $(SRC)
|
||||
else
|
||||
SRC := keymap_plain.c $(SRC)
|
||||
endif
|
||||
|
||||
CONFIG_H = config_tmk_rev1.h
|
||||
|
||||
|
||||
# MCU name
|
||||
MCU = atmega32u4
|
||||
|
||||
# Processor frequency.
|
||||
# This will define a symbol, F_CPU, in all source code files equal to the
|
||||
# processor frequency in Hz. You can then use this symbol in your source code to
|
||||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||||
# automatically to create a 32-bit value in your source code.
|
||||
#
|
||||
# This will be an integer division of F_USB below, as it is sourced by
|
||||
# F_USB after it has run through any CPU prescalers. Note that this value
|
||||
# does not *change* the processor frequency - it should merely be updated to
|
||||
# reflect the processor speed set externally so that the code can use accurate
|
||||
# software delays.
|
||||
F_CPU = 16000000
|
||||
|
||||
|
||||
#
|
||||
# LUFA specific
|
||||
#
|
||||
# Target architecture (see library "Board Types" documentation).
|
||||
ARCH = AVR8
|
||||
|
||||
# Input clock frequency.
|
||||
# This will define a symbol, F_USB, in all source code files equal to the
|
||||
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
||||
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
||||
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
||||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
||||
# at the end, this will be done automatically to create a 32-bit value in your
|
||||
# source code.
|
||||
#
|
||||
# If no clock division is performed on the input clock inside the AVR (via the
|
||||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||||
F_USB = $(F_CPU)
|
||||
|
||||
|
||||
# Boot Section Size in *bytes*
|
||||
# Teensy halfKay 512
|
||||
# Teensy++ halfKay 1024
|
||||
# Atmel DFU loader 4096
|
||||
# LUFA bootloader 4096
|
||||
# USBaspLoader 2048
|
||||
OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
||||
|
||||
|
||||
# Build Options
|
||||
# comment out to disable the options.
|
||||
#
|
||||
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
|
||||
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
|
||||
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
|
||||
CONSOLE_ENABLE = yes # Console for debug(+400)
|
||||
COMMAND_ENABLE = yes # Commands for debug and configuration
|
||||
#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
|
||||
|
||||
|
||||
# PS/2 Options
|
||||
#
|
||||
PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened)
|
||||
#PS2_USE_BUSYWAIT = yes # uses primitive reference code
|
||||
|
||||
|
||||
# Search Path
|
||||
VPATH += $(TARGET_DIR)
|
||||
VPATH += $(TOP_DIR)
|
||||
|
||||
include $(TOP_DIR)/protocol.mk
|
||||
include $(TOP_DIR)/protocol/lufa.mk
|
||||
include $(TOP_DIR)/common.mk
|
||||
include $(TOP_DIR)/rules.mk
|
||||
|
|
@ -0,0 +1,98 @@
|
|||
#
|
||||
# Makefile for TMK keyboard converter rev2
|
||||
# https://github.com/tmk/keyboard_converter#pcb-rev2
|
||||
#
|
||||
# Target file name (without extension).
|
||||
TARGET = ps2_usb_tmk_rev2
|
||||
|
||||
# Directory common source filess exist
|
||||
TOP_DIR = ../..
|
||||
|
||||
# Directory keyboard dependent files exist
|
||||
TARGET_DIR = .
|
||||
|
||||
# project specific files
|
||||
SRC = keymap_common.c \
|
||||
matrix.c \
|
||||
led.c
|
||||
|
||||
ifdef KEYMAP
|
||||
SRC := keymap_$(KEYMAP).c $(SRC)
|
||||
else
|
||||
SRC := keymap_plain.c $(SRC)
|
||||
endif
|
||||
|
||||
CONFIG_H = config_tmk_rev2.h
|
||||
|
||||
|
||||
# MCU name
|
||||
MCU = atmega32u2
|
||||
|
||||
# Processor frequency.
|
||||
# This will define a symbol, F_CPU, in all source code files equal to the
|
||||
# processor frequency in Hz. You can then use this symbol in your source code to
|
||||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||||
# automatically to create a 32-bit value in your source code.
|
||||
#
|
||||
# This will be an integer division of F_USB below, as it is sourced by
|
||||
# F_USB after it has run through any CPU prescalers. Note that this value
|
||||
# does not *change* the processor frequency - it should merely be updated to
|
||||
# reflect the processor speed set externally so that the code can use accurate
|
||||
# software delays.
|
||||
F_CPU = 16000000
|
||||
|
||||
|
||||
#
|
||||
# LUFA specific
|
||||
#
|
||||
# Target architecture (see library "Board Types" documentation).
|
||||
ARCH = AVR8
|
||||
|
||||
# Input clock frequency.
|
||||
# This will define a symbol, F_USB, in all source code files equal to the
|
||||
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
||||
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
||||
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
||||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
||||
# at the end, this will be done automatically to create a 32-bit value in your
|
||||
# source code.
|
||||
#
|
||||
# If no clock division is performed on the input clock inside the AVR (via the
|
||||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||||
F_USB = $(F_CPU)
|
||||
|
||||
|
||||
# Boot Section Size in *bytes*
|
||||
# Teensy halfKay 512
|
||||
# Teensy++ halfKay 1024
|
||||
# Atmel DFU loader 4096
|
||||
# LUFA bootloader 4096
|
||||
# USBaspLoader 2048
|
||||
OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
||||
|
||||
|
||||
# Build Options
|
||||
# comment out to disable the options.
|
||||
#
|
||||
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
|
||||
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
|
||||
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
|
||||
CONSOLE_ENABLE = yes # Console for debug(+400)
|
||||
COMMAND_ENABLE = yes # Commands for debug and configuration
|
||||
#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
|
||||
|
||||
|
||||
# PS/2 Options
|
||||
#
|
||||
PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin
|
||||
#PS2_USE_BUSYWAIT = yes # uses primitive reference code
|
||||
|
||||
|
||||
# Search Path
|
||||
VPATH += $(TARGET_DIR)
|
||||
VPATH += $(TOP_DIR)
|
||||
|
||||
include $(TOP_DIR)/protocol.mk
|
||||
include $(TOP_DIR)/protocol/lufa.mk
|
||||
include $(TOP_DIR)/common.mk
|
||||
include $(TOP_DIR)/rules.mk
|
||||
|
|
@ -1,11 +1,50 @@
|
|||
PS/2 to USB keyboard converter
|
||||
==============================
|
||||
This firmware converts PS/2 keyboard protocol to USB and supports only Scan Code Set 2.
|
||||
This firmware converts PS/2 keyboard protocol to USB.(It supports Scan Code Set 2.)
|
||||
|
||||
|
||||
Connect Wires
|
||||
-------------
|
||||
In case of Teensy2.0(ATMega32U4):
|
||||
|
||||
1. Connect **Vcc** and **GND**.
|
||||
2. Connect **Clock** and **Data** line.
|
||||
- **Interrupt**: **Clock** is on `PD1` and **Data** on `PD0`.(Recommended. Soarer's converter compatible)
|
||||
- **Busywait**: **Clock** is on `PD1` and **Data** on `PD0`.
|
||||
- **USART**: **Clock** is on `PD5` and **Data** on `PD2`.
|
||||
3. Optionally you need pull-up register. 1K-10K Ohm is OK.
|
||||
|
||||
To change pin configuration edit config.h.
|
||||
|
||||
|
||||
Build Firmware
|
||||
--------------
|
||||
For **PJRC Teensy** just run `make`:
|
||||
|
||||
$ make clean
|
||||
$ make
|
||||
|
||||
To select keymap:
|
||||
|
||||
$ make clean
|
||||
$ make KEYMAP=[plain|jis|spacefn|...]
|
||||
|
||||
After that you will find HEX file `ps2_usb_lufa.hex` in current directory.
|
||||
|
||||
|
||||
- For **TMK converter Rev.1** use `make -f Makefile.tmk_rev1` instead of `make` and HEX file is `ps2_usb_tmk_rev1.hex`.
|
||||
|
||||
- For **TMK converter Rev.2** use `make -f Makefile.tmk_rev2` instead of `make` and HEX file is `ps2_usb_tmk_rev2.hex`.
|
||||
|
||||
|
||||
Keymap
|
||||
------
|
||||
Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `keymap_<name>.c` and see keymap document(you can find in README.md of top directory) and existent keymap files.
|
||||
|
||||
|
||||
PS/2 signal handling implementations
|
||||
------------------------------------
|
||||
Following three methods are used to implement PS/2 signal handling.
|
||||
Following three methods can be used to implement PS/2 signal handling.
|
||||
|
||||
### Simple and stupid busy-wait(ps2_busywait.c)
|
||||
This is expected to implemented with portable C code for reference.
|
||||
|
|
@ -17,36 +56,6 @@ Following three methods are used to implement PS/2 signal handling.
|
|||
To select method edit Makefile.
|
||||
|
||||
|
||||
Connect Wires
|
||||
-------------
|
||||
In case of Teensy2.0(ATMega32U4):
|
||||
|
||||
1. Connect Vcc and GND.
|
||||
2. Connect Clock and Data line.
|
||||
- Busywait: Clock is on PD5 and Data on PD2.
|
||||
- Interrupt: Clock is on PD1 and Data on PD2.
|
||||
- USART: Clock is on PD5 and Data on PD2.
|
||||
3. Optionally you need pull-up register. 1K-10K Ohm is OK.
|
||||
|
||||
To change pin configuration edit config.h.
|
||||
|
||||
|
||||
Build Firmware
|
||||
--------------
|
||||
Just run `make`:
|
||||
|
||||
$ make
|
||||
|
||||
To select keymap:
|
||||
|
||||
$ make KEYMAP=[plain|jis|spacefn|...]
|
||||
|
||||
|
||||
Keymap
|
||||
------
|
||||
Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `keymap_<name>.c` and see keymap document(you can find in top README.md) and existent keymap files.
|
||||
|
||||
|
||||
V-USB Support
|
||||
-------------
|
||||
You can also use this converter on ATmega(168/328) with V-USB instead of Teensy.
|
||||
|
|
|
|||
|
|
@ -0,0 +1,147 @@
|
|||
/*
|
||||
Copyright 2012 Jun Wako <wakojun@gmail.com>
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 2 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#ifndef CONFIG_H
|
||||
#define CONFIG_H
|
||||
|
||||
#include <avr/interrupt.h>
|
||||
|
||||
#define VENDOR_ID 0xFEED
|
||||
#define PRODUCT_ID 0x6512
|
||||
#define DEVICE_VER 0x0001
|
||||
#define MANUFACTURER t.m.k.
|
||||
#define PRODUCT PS/2 keyboard converter
|
||||
#define DESCRIPTION convert PS/2 keyboard to USB
|
||||
|
||||
|
||||
/* matrix size */
|
||||
#define MATRIX_ROWS 32 // keycode bit: 3-0
|
||||
#define MATRIX_COLS 8 // keycode bit: 6-4
|
||||
|
||||
|
||||
/* key combination for command */
|
||||
#define IS_COMMAND() ( \
|
||||
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) || \
|
||||
keyboard_report->mods == (MOD_BIT(KC_LCTRL) | MOD_BIT(KC_RSHIFT)) \
|
||||
)
|
||||
|
||||
|
||||
//#define NO_SUSPEND_POWER_DOWN
|
||||
|
||||
|
||||
/*
|
||||
* PS/2 Busywait
|
||||
*/
|
||||
#ifdef PS2_USE_BUSYWAIT
|
||||
#define PS2_CLOCK_PORT PORTD
|
||||
#define PS2_CLOCK_PIN PIND
|
||||
#define PS2_CLOCK_DDR DDRD
|
||||
#define PS2_CLOCK_BIT 5
|
||||
#define PS2_DATA_PORT PORTD
|
||||
#define PS2_DATA_PIN PIND
|
||||
#define PS2_DATA_DDR DDRD
|
||||
#define PS2_DATA_BIT 2
|
||||
#endif
|
||||
|
||||
/*
|
||||
* PS/2 USART
|
||||
*/
|
||||
#ifdef PS2_USE_USART
|
||||
#if defined(__AVR_ATmega16U4__) || defined(__AVR_ATmega32U4__)
|
||||
/* XCK for clock line and RXD for data line */
|
||||
#define PS2_CLOCK_PORT PORTD
|
||||
#define PS2_CLOCK_PIN PIND
|
||||
#define PS2_CLOCK_DDR DDRD
|
||||
#define PS2_CLOCK_BIT 5
|
||||
#define PS2_DATA_PORT PORTD
|
||||
#define PS2_DATA_PIN PIND
|
||||
#define PS2_DATA_DDR DDRD
|
||||
#define PS2_DATA_BIT 2
|
||||
/* synchronous, odd parity, 1-bit stop, 8-bit data, sample at falling edge */
|
||||
/* set DDR of CLOCK as input to be slave */
|
||||
#define PS2_USART_INIT() do { \
|
||||
PS2_CLOCK_DDR &= ~(1<<PS2_CLOCK_BIT); \
|
||||
PS2_DATA_DDR &= ~(1<<PS2_DATA_BIT); \
|
||||
UCSR1C = ((1 << UMSEL10) | \
|
||||
(3 << UPM10) | \
|
||||
(0 << USBS1) | \
|
||||
(3 << UCSZ10) | \
|
||||
(0 << UCPOL1)); \
|
||||
UCSR1A = 0; \
|
||||
UBRR1H = 0; \
|
||||
UBRR1L = 0; \
|
||||
} while (0)
|
||||
#define PS2_USART_RX_INT_ON() do { \
|
||||
UCSR1B = ((1 << RXCIE1) | \
|
||||
(1 << RXEN1)); \
|
||||
} while (0)
|
||||
#define PS2_USART_RX_POLL_ON() do { \
|
||||
UCSR1B = (1 << RXEN1); \
|
||||
} while (0)
|
||||
#define PS2_USART_OFF() do { \
|
||||
UCSR1C = 0; \
|
||||
UCSR1B &= ~((1 << RXEN1) | \
|
||||
(1 << TXEN1)); \
|
||||
} while (0)
|
||||
#define PS2_USART_RX_READY (UCSR1A & (1<<RXC1))
|
||||
#define PS2_USART_RX_DATA UDR1
|
||||
#define PS2_USART_ERROR (UCSR1A & ((1<<FE1) | (1<<DOR1) | (1<<UPE1)))
|
||||
#define PS2_USART_RX_VECT USART1_RX_vect
|
||||
#elif defined(__AVR_ATmega168__) || defined(__AVR_ATmega168P__) || defined(__AVR_ATmega328P__)
|
||||
/* XCK for clock line and RXD for data line */
|
||||
#define PS2_CLOCK_PORT PORTD
|
||||
#define PS2_CLOCK_PIN PIND
|
||||
#define PS2_CLOCK_DDR DDRD
|
||||
#define PS2_CLOCK_BIT 4
|
||||
#define PS2_DATA_PORT PORTD
|
||||
#define PS2_DATA_PIN PIND
|
||||
#define PS2_DATA_DDR DDRD
|
||||
#define PS2_DATA_BIT 0
|
||||
/* synchronous, odd parity, 1-bit stop, 8-bit data, sample at falling edge */
|
||||
/* set DDR of CLOCK as input to be slave */
|
||||
#define PS2_USART_INIT() do { \
|
||||
PS2_CLOCK_DDR &= ~(1<<PS2_CLOCK_BIT); \
|
||||
PS2_DATA_DDR &= ~(1<<PS2_DATA_BIT); \
|
||||
UCSR0C = ((1 << UMSEL00) | \
|
||||
(3 << UPM00) | \
|
||||
(0 << USBS0) | \
|
||||
(3 << UCSZ00) | \
|
||||
(0 << UCPOL0)); \
|
||||
UCSR0A = 0; \
|
||||
UBRR0H = 0; \
|
||||
UBRR0L = 0; \
|
||||
} while (0)
|
||||
#define PS2_USART_RX_INT_ON() do { \
|
||||
UCSR0B = ((1 << RXCIE0) | \
|
||||
(1 << RXEN0)); \
|
||||
} while (0)
|
||||
#define PS2_USART_RX_POLL_ON() do { \
|
||||
UCSR0B = (1 << RXEN0); \
|
||||
} while (0)
|
||||
#define PS2_USART_OFF() do { \
|
||||
UCSR0C = 0; \
|
||||
UCSR0B &= ~((1 << RXEN0) | \
|
||||
(1 << TXEN0)); \
|
||||
} while (0)
|
||||
#define PS2_USART_RX_READY (UCSR0A & (1<<RXC0))
|
||||
#define PS2_USART_RX_DATA UDR0
|
||||
#define PS2_USART_ERROR (UCSR0A & ((1<<FE0) | (1<<DOR0) | (1<<UPE0)))
|
||||
#define PS2_USART_RX_VECT USART_RX_vect
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#endif
|
||||
|
|
@ -0,0 +1,86 @@
|
|||
/*
|
||||
Copyright 2012 Jun Wako <wakojun@gmail.com>
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 2 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#ifndef CONFIG_H
|
||||
#define CONFIG_H
|
||||
|
||||
#include <avr/interrupt.h>
|
||||
|
||||
#define VENDOR_ID 0xFEED
|
||||
#define PRODUCT_ID 0x6512
|
||||
#define DEVICE_VER 0x0001
|
||||
#define MANUFACTURER t.m.k.
|
||||
#define PRODUCT PS/2 keyboard converter
|
||||
#define DESCRIPTION convert PS/2 keyboard to USB
|
||||
|
||||
|
||||
/* matrix size */
|
||||
#define MATRIX_ROWS 32 // keycode bit: 3-0
|
||||
#define MATRIX_COLS 8 // keycode bit: 6-4
|
||||
|
||||
|
||||
/* key combination for command */
|
||||
#define IS_COMMAND() ( \
|
||||
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) || \
|
||||
keyboard_report->mods == (MOD_BIT(KC_LCTRL) | MOD_BIT(KC_RSHIFT)) \
|
||||
)
|
||||
|
||||
|
||||
//#define NO_SUSPEND_POWER_DOWN
|
||||
|
||||
|
||||
/*
|
||||
* PS/2 Busywait
|
||||
*/
|
||||
#ifdef PS2_USE_BUSYWAIT
|
||||
#define PS2_CLOCK_PORT PORTD
|
||||
#define PS2_CLOCK_PIN PIND
|
||||
#define PS2_CLOCK_DDR DDRD
|
||||
#define PS2_CLOCK_BIT 1
|
||||
#define PS2_DATA_PORT PORTD
|
||||
#define PS2_DATA_PIN PIND
|
||||
#define PS2_DATA_DDR DDRD
|
||||
#define PS2_DATA_BIT 0
|
||||
#endif
|
||||
|
||||
/*
|
||||
* PS/2 Pin interrupt
|
||||
*/
|
||||
#ifdef PS2_USE_INT
|
||||
/* uses INT1 for clock line(ATMega32U4) */
|
||||
#define PS2_CLOCK_PORT PORTD
|
||||
#define PS2_CLOCK_PIN PIND
|
||||
#define PS2_CLOCK_DDR DDRD
|
||||
#define PS2_CLOCK_BIT 1
|
||||
#define PS2_DATA_PORT PORTD
|
||||
#define PS2_DATA_PIN PIND
|
||||
#define PS2_DATA_DDR DDRD
|
||||
#define PS2_DATA_BIT 0
|
||||
#define PS2_INT_INIT() do { \
|
||||
EICRA |= ((1<<ISC11) | \
|
||||
(0<<ISC10)); \
|
||||
} while (0)
|
||||
#define PS2_INT_ON() do { \
|
||||
EIMSK |= (1<<INT1); \
|
||||
} while (0)
|
||||
#define PS2_INT_OFF() do { \
|
||||
EIMSK &= ~(1<<INT1); \
|
||||
} while (0)
|
||||
#define PS2_INT_VECT INT1_vect
|
||||
#endif
|
||||
|
||||
#endif
|
||||
Loading…
Reference in New Issue