67 lines
2.4 KiB
Makefile
67 lines
2.4 KiB
Makefile
# MCU name
|
|
MCU ?= atmega32u4
|
|
|
|
|
|
# Processor frequency.
|
|
# This will define a symbol, F_CPU, in all source code files equal to the
|
|
# processor frequency in Hz. You can then use this symbol in your source code to
|
|
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
|
# automatically to create a 32-bit value in your source code.
|
|
#
|
|
# This will be an integer division of F_USB below, as it is sourced by
|
|
# F_USB after it has run through any CPU prescalers. Note that this value
|
|
# does not *change* the processor frequency - it should merely be updated to
|
|
# reflect the processor speed set externally so that the code can use accurate
|
|
# software delays.
|
|
F_CPU ?= 8000000
|
|
|
|
|
|
#
|
|
# LUFA specific
|
|
#
|
|
# Target architecture (see library "Board Types" documentation).
|
|
ARCH ?= AVR8
|
|
|
|
# Input clock frequency.
|
|
# This will define a symbol, F_USB, in all source code files equal to the
|
|
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
|
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
|
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
|
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
|
# at the end, this will be done automatically to create a 32-bit value in your
|
|
# source code.
|
|
#
|
|
# If no clock division is performed on the input clock inside the AVR (via the
|
|
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
|
F_USB ?= $(F_CPU)
|
|
|
|
# Interrupt driven control endpoint task
|
|
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
|
|
|
|
|
# Boot Section Size in *bytes*
|
|
# Teensy halfKay 512
|
|
# Teensy++ halfKay 1024
|
|
# Atmel DFU loader 4096
|
|
# LUFA bootloader 4096
|
|
# USBaspLoader 2048
|
|
OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
|
|
|
|
|
# Build Options
|
|
# comment out to disable the options.
|
|
#
|
|
# BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
|
|
# MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
|
|
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
|
|
# CONSOLE_ENABLE ?= yes # Console for debug(+400)
|
|
# COMMAND_ENABLE ?= yes # Commands for debug and configuration
|
|
# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend
|
|
# NKRO_ENABLE ?= yes # USB Nkey Rollover - not yet supported in LUFA
|
|
# BACKLIGHT_ENABLE ?= yes
|
|
|
|
|
|
CUSTOM_MATRIX = yes
|
|
SRC = custom_matrix.cpp
|
|
include $(TMK_DIR)/protocol/usb_hid.mk
|