qmk_firmware/keyboard/hhkb/not_supported/Makefile.iwrap

#
# Makefile for iWRAP
#


# Target file name (without extension).
TARGET = hhkb_iwrap

# Directory common source filess exist
TMK_DIR = ../..

# Directory keyboard dependent files exist
TARGET_DIR = .

# keyboard dependent files
SRC =	\
	keymap.c \
	matrix.c \
	led.c

CONFIG_H = config_iwrap.h


# V-USB debug level: To use ps2_usart.c level must be 0
# ps2_usart.c requires USART to receive PS/2 signal.
OPT_DEFS = -DDEBUG_LEVEL=0


# MCU name, you MUST set this to match the board you are using
# type "make clean" after changing this, so all files will be rebuilt
MCU = atmega328p


# Processor frequency.
#   Normally the first thing your program should do is set the clock prescaler,
#   so your program will run at the correct speed.  You should also set this
#   variable to same clock speed.  The _delay_ms() macro uses this, and many
#   examples use this variable to calculate timings.  Do not add a "UL" here.
F_CPU = 12000000


# Boot Section Size in *bytes*
#   Teensy halfKay   512
#   Teensy++ halfKay 1024
#   Atmel DFU loader 4096
#   LUFA bootloader  4096
#   USBaspLoader     2048
OPT_DEFS += -DBOOTLOADER_SIZE=2048


# Build Options
#   comment out to disable the options.
#
BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration
MOUSEKEY_ENABLE = yes	# Mouse keys
EXTRAKEY_ENABLE = yes	# Audio control and System control
CONSOLE_ENABLE = yes	# Console for debug
COMMAND_ENABLE = yes    # Commands for debug and configuration
#NKRO_ENABLE = yes	# USB Nkey Rollover



#---------------- Programming Options --------------------------
AVRDUDE = avrdude
# Type: avrdude -c ? to get a full listing.
AVRDUDE_PROGRAMMER = usbasp
AVRDUDE_PORT =
AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep

# Uncomment the following if you want avrdude's erase cycle counter.
# Note that this counter needs to be initialized first using -Yn,
# see avrdude manual.
#AVRDUDE_ERASE_COUNTER = -y

# Uncomment the following if you do /not/ wish a verification to be
# performed after programming the device.
#AVRDUDE_NO_VERIFY = -V

# Increase verbosity level.  Please use this when submitting bug
# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude> 
# to submit bug reports.
#AVRDUDE_VERBOSE = -v -v

#AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER)
AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)

PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)



# Search Path
VPATH += $(TARGET_DIR)
VPATH += $(TMK_DIR)

include $(TMK_DIR)/protocol/iwrap.mk
# TODO: to be selectable: V-USB, LUFA or PJRC
#include $(TMK_DIR)/protocol/vusb.mk
include $(TMK_DIR)/common.mk
include $(TMK_DIR)/rules.mk